SENTINEL CONNECTOR SYSTEMS - WHEN SIGNAL INTEGRITY MATTERS
VETERAN OWNED BUSINESS ENTERPRISE - MADE IN USA
1,000,000 Plugs Built Every Day + 20,000 Cable Assemblies
VETERAN OWNED BUSINESS ENTERPRISE (VOBE)
Download Interactive Belden-Sentinel RJ-45 Plug Cross Reference .XLS Spreadsheet
BELDEN® Category 5e DataTuff® Twisted Pair Cable
Industrial Ethernet, Harsh Environments, Flexible Applications, 200MHz Category 5e, Industrial Patch Cable, Gigabit Ethernet, 100BaseTX, 100BaseVG ANYLAN, 155ATM, 622ATM, NTSC/PAL Component or Composite Video, AES/EBU, Digital Video, RS-422, CMX - Outdoor, RJ-45 Compatible
7939A - 24 AWG stranded (7x32) bare copper conductors, bonded pairs, polyolefin insulation, polyester separator, Beldfoil® shield (100% coverage), drain wire, industrial grade sunlight- and oil-resistant PVC jacket. Sequential marking at two foot intervals.
* Shielded RJ45 plug with integral "C CRIMP" for increased shield effectiveness, added cable stress relief and additional strength. Accepts up to a .310" cable jacket OD
* Incorporates a PATENTED CONDUCTIVE NEXT Reduction System. In addition to providing PRECISE CONDUCTOR ALIGNMENT, the Composite Carbon/Graphite Fiber Conductor Load Bar GREATLY REDUCES NEXT and RETURN LOSS by ABSORBING REFLECTIONS and CHANNELING IT AWAY FROM THE CONDUCTORS. Using recommended termination procedures and equipment, ANSI/TIA/EIA 568 Category 6 performance levels are achievable with good workmanship and certified cables.
* Utilizes a 4 over 4 contact design (4 LONG and 4 SHORT) that provides increased isolation and spatial dispersion within the plug to minimize crosstalk and accepts .044" - 048" CONDUCTOR OD.
* The conductors are isolated by the Conductor Load Bar and through Plastic Isolation/Insulation Barriers where contact termination is made, thereby improving electrical performance.
* Plug accepts both SOLID or STRANDED conductors
* Made in USA
111S08080090H34 Specifications
Performance: Meets or Exceeds ANSI/TIA/EIA 568 - ANSI/TIA 1096-A (Formerly FCC Part 68) - CENELEC EN 50173 -
IEC 60603 - ISO-8877 - ISO/IEC 11801
Contact Material: Phosphor Bronze - .012" thick
Contact Plating: Minimum 50 Micro-Inch Pure Gold - Selective 24 Carat Hard Gold Plate in contact area over 100 Micro-Inch minimum Nickel Plate. Exceeds TIA-1096 specifications (formerly FCC Part 68)
Plug Material: Polycarbonate
Plug Tolerances and Dimensions: Meets TIA-1096 specifications (formerly FCC Part 68)
UL Recognized: UL File #E188111
Flame Autoextinguish: 94-V0
Operating Temperature: -40º C to +85º C
Insertion/Extraction Life: 1000 Minimum Cycles
Contact Resistance: 10 Milli-Ohms maximum
Current/Voltage: 30 VAC/42 VDC at 1.5 Amps
Compliance: RoHS Compliant
111S08080090H34 Termination Instructions
PROPER CABLE PREPARATION INCLUDES COPPER SHIELDING TAPE TO MAINTAIN SHIELD INTEGRITY & PROVIDING A PLACE FOR THE "C CRIMP" SHIELD ON THE CABLE
DO NOT TAKE THIS STEP FOR GRANTED
Cable assemblies built using inadequate or poor quality tools and dies.....worn out tooling.....or mismatched tooling, WILL HAVE A MAJOR IMPACT ON THE PERFORMANCE OF THE CABLE ASSEMBLY.
Heat Shrink - 3M™ Heat Shrink Tubing EPS-300
Adhesive-Lined, 3:1, Flexible, Polyolefin
"Lock" Everything in Place
CAVEAT EMPTOR.....Let The Buyer Beware
SUB-STANDARD, NON-COMPLIANT and COUNTERFEIT RJ45's coming in from the Far East
KNOW THE STANDARDS - KNOW THE SPECS - INSIST ON COMPLIANCE - KNOW YOUR SUPPLIERSdave@rj45s.com
RJ45s.com
2400 East Main Street
St Charles, IL 60174
phone: 630-659-6337
fax: 888-210-4593
